A well pump is an integral part of a household. It is especially so if you live in the countryside where the water piping does not reach. The pressure level of your water is a crucial tool in the delivery of water. If you are looking for ways to increase water pressure on your well pump, below is a guide on safely doing so.
How To Increase Water Pressure On Well Pump - Steps
1. Check Your Pipes
Low pressure in your well pumps may be caused by clogged pipes filled with sediment build-ups and minerals. It is not uncommon for build-ups to occur in your pipes, mostly if you reside in areas rich in minerals. Most pump owners automatically assume low pressure in their pumps is caused by the pressure control switch, while in a real sense, it could be clogged pipes.
After checking the pipes, you should also check the showerheads since the water pressure may be okay, but mineral build-ups slow down water flow.
2. Elevate Pressure Settings
Set pressure settings on a standard pressure system also ascertain when the pump goes off and on. The highest number represents the PSI turning them off while the lowest represents the PSI turning on the pump. The ordinary settings on a pressure system include; 30/50, 20/40, 40/60.
Ordinarily, the higher the pressure settings, the higher the well pump pressure. Try increasing the pressure settings to increase the water pressure from the well pump. To elevate the pressure setting, ensure you turn off the electricity supply to the switch to avoid potential electrical harm. The majority of pressure switch manufacturers label the process of adjusting the settings.
3. Constant Pressure Valve
A constant pressure valve is a mechanical equipment designed to maintain a consistent water flow by lowering the pump cycles. An ordinary pressure system depends on the pressure tank and well pump to supply water pressure via a series of off and on cycles.
A pressure tank is designed to protect the pump from needless usage by saving pressurized water. However, the well pump's wear is likely caused by regular starting and stopping instead of consistent use. Dispensing and consistent filling of the water tank also causes instability in water pressure.
Installing the constant pressure valve comes with a few benefits;
4. Additional Pressure Tank
A standard pressure system depends on the normal dispensing and filling of the tank. Therefore, you may notice unnecessary fluctuations in pressure as water comes out more at peak hours. You should note that an additional tank or a replacement does not necessarily mean an increase in water pressure past your pressure settings.
Replace your pressure tank with a bigger one or add another tank that will elevate the well system's drawdown capacity. This will accommodate a greater demand, especially during peak hours, and supply a steady water pressure for an extended time.
5. Pressure Booster Pump
A longer distance between your well pump and exit point can also cause low water pressure. For example, in tall stories buildings, the well pump has to rival gravity in supplying adequate water to the highest floor. It often leads to a flow rate drop for higher floor fixtures.
Likewise, some houses depend on a community well supplying various neighborhoods with the same water. In such a case, homes situated at the supply line's end tend to experience reduced water pressure than the rest.
If distance and gravity are causing you pressure reduction from the well, install a best pressure booster pump to increase the pressure. The device uses impellers and a motor to elevate water flow.
Before installing your pressure booster pump in the well where you have a submersible water pump, install a pressure regulator valve that will ensure the system is not over-pressurized.
6. Constant Pressure System
Standard pressure systems depend on the pressure tank, well pump, and the switch to regulate water flow. Most of these systems only the off and on settings. You will most likely feel fluctuations between low and high pressure as you use your water.
Installing a constant pressure system will ensure you do not need to be regularly and manually controlling pressure. The continuous pressure system has different components. It has a variable speed pump that adjusts the speed of pressure depending on your water usage. It also has a variable speed pump, controlling the pump's speed.
The benefits of using a constant pressure system to control water pressure from well pump are;
Causes of Low Water Pressure.
Bottom Line
One way to ensure smooth and increased water pressure on your well pump is maintenance. Check your pipes regularly for clogs and clean if necessary. Also, you can try adjusting the pressure switch a little higher. If none of these is useful, try installing any of the devices mentioned above that will help you to increase water pressure on the well pump.